expired Posted by cafe-con-leche • May 3, 2022
May 3, 2022 5:05 AM
Item 1 of 5
Item 1 of 5
expired Posted by cafe-con-leche • May 3, 2022
May 3, 2022 5:05 AM
DEWALT 15-Amp Corded 8-1/4" Compact Portable Jobsite Table Saw
+ Free Shipping$272
$379
28% offAmazon
Visit AmazonGood Deal
Bad Deal
Save
Share
17 Comments
Sign up for a Slickdeals account to remove this ad.
It's not for finishing work, or high precision cuts. It's there just to do quick rips for people that live in 1980's still and don't know that track saws exist lmao jk.
So it's a heavier, older way to rip.
Dewalt has their 10" saw still. I'd assume that can handle dado stacks, but I'd never trust running a stack in one of these cheaper designed saws. A router would be far more efficient.
Personally, I always found it strange that table saws were still used in woodworking. Old habits die hard I suppose, but I'd assume a router would be far easier than having to change out your table saw blade, put a stack in it, and then go back to your blade. I'd rather just put an edge guide, and route my dado's.
even the old 10" dewalt only has 1 model that takes dado stacks. but like mentioned above, these really arent cabinet saws, they are great for ripping OSB/plywood or dimensional lumber.
I've had this model since release and its been great for any house projects ive needed it for.
It's not for finishing work, or high precision cuts. It's there just to do quick rips for people that live in 1980's still and don't know that track saws exist lmao jk.
So it's a heavier, older way to rip.
Dewalt has their 10" saw still. I'd assume that can handle dado stacks, but I'd never trust running a stack in one of these cheaper designed saws. A router would be far more efficient.
Personally, I always found it strange that table saws were still used in woodworking. Old habits die hard I suppose, but I'd assume a router would be far easier than having to change out your table saw blade, put a stack in it, and then go back to your blade. I'd rather just put an edge guide, and route my dado's.
I'll disagree on the precision work though. A small saw like this should be for the precision work. The very specific cuts for cabinetry, etc. Not saying this saw will do that though. This saw will/should be able to do the thinner rips that a track saw is too bulky to do.
even the old 10" dewalt only has 1 model that takes dado stacks. but like mentioned above, these really arent cabinet saws, they are great for ripping OSB/plywood or dimensional lumber.
I've had this model since release and its been great for any house projects ive needed it for.
FYI - I had paid $299, which was retail at the time for the Skil. Looks like it has moved to $349 with inflation.
It's not for finishing work, or high precision cuts. It's there just to do quick rips for people that live in 1980's still and don't know that track saws exist lmao jk.
So it's a heavier, older way to rip.
Dewalt has their 10" saw still. I'd assume that can handle dado stacks, but I'd never trust running a stack in one of these cheaper designed saws. A router would be far more efficient.
Personally, I always found it strange that table saws were still used in woodworking. Old habits die hard I suppose, but I'd assume a router would be far easier than having to change out your table saw blade, put a stack in it, and then go back to your blade. I'd rather just put an edge guide, and route my dado's.
However, my father-in-law is an avid woodworker. He has recently invested in a good saw with a fence that cost more than the saw. Once he got it tuned, it is by far the most accurate piece of equipment he owns. He even prefers to make miter cuts on it, unless he's breaking down larger stock. With the right jig, he feels his table saw is his go-to solution for most things.
I disagree with him on a lot of points. And I agree with you on the router being a great option for a lot of work. I guess it comes down to each persons preferences and the type of woodworking they are into.
But, to keep it on topic somewhat, I agree with the persons above that this saw should only be used for smaller and rougher work. Someone with patience should be able to tune it up (if it has the adjustments), make a zero clearance fence and do some finer work on it with a good blade.
Sign up for a Slickdeals account to remove this ad.
It's not for finishing work, or high precision cuts. It's there just to do quick rips for people that live in 1980's still and don't know that track saws exist lmao jk.
So it's a heavier, older way to rip.
Dewalt has their 10" saw still. I'd assume that can handle dado stacks, but I'd never trust running a stack in one of these cheaper designed saws. A router would be far more efficient.
Personally, I always found it strange that table saws were still used in woodworking. Old habits die hard I suppose, but I'd assume a router would be far easier than having to change out your table saw blade, put a stack in it, and then go back to your blade. I'd rather just put an edge guide, and route my dado's.
Which makes precision not great.
Haven't seen it priced this low since the beginning of 2020 (I paid $279.00 in May 2020)
Yeah it doesn't take dado stacks but that why I have my Bosche router.
The fence system on this is great. If you're concerned about the size of the saw, go to Lowes and compare it to the 10 inch saws and see if that is an issue with you. For me it wasn't.
I just bought the DEWALT Table Saw Stand for it (DWE74911) and it works flawlessly.
If you're gonna do finish work I recommend upgrading the blade to a good finish blade. I got a $40ish Freud/Diablo plywood cutting blade for it.
https://www.amazon.com/DEWALT-Job...7FZ8A?th=
Haven't seen it priced this low since the beginning of 2020 (I paid $279.00 in May 2020)
Yeah it doesn't take dado stacks but that why I have my Bosche router.
The fence system on this is great. If you're concerned about the size of the saw, go to Lowes and compare it to the 10 inch saws and see if that is an issue with you. For me it wasn't.
I just bought the DEWALT Table Saw Stand for it (DWE74911) and it works flawlessly.
If you're gonna do finish work I recommend upgrading the blade to a good finish blade. I got a $40ish Freud/Diablo plywood cutting blade for it.
Also, at this price I feel like one could sell it for a small loss if they end up outgrowing it.
And no, no dados.
I've owned this saw for almost 2 years now and I have nothing but good things to say about it. The blade that comes with it works perfectly fine and the fence is fantastic. The miter gauge is garbage but most stock ones are. The blade speed is what makes it better for ripping though.
Sign up for a Slickdeals account to remove this ad.